Difference between revisions of "LTE UE Connection Status"

From YateBTS
Jump to: navigation, search
(updated for newer software revisions)
(updated for new revision)
Line 1: Line 1:
This page documents the '''enb uepool chans''' command, as of r7293.
+
This page documents the '''enb uepool chans''' command, by revision, most recent first.
 +
 
 +
 
 +
== As of r7437 ==
 +
 
 +
* '''RNTI''' - RNTI (radio layer connection ID) of this connection.
 +
** If this number is followed by '''R''', it means the connection is marked for release but not yet fully released.
 +
** If this number is followed by '''S''', that means it is a simulated UE generated internally by the eNodeB.
 +
* '''PHR''' - Power headroom in dB per resource block.
 +
* '''RSSIdB''' - Recent average PUSCH UL RSSI, referenced to the receiver saturation point.
 +
* '''RSSIdB''' - Recent average PUSCH UL RSSI in true dBm.
 +
* '''UL-SNR''' - Short-term average PUSCH UL signal to noise ratio in dB, which should be 12 or higher for a good connection.
 +
* '''UL-FER''' - Short-term UL transport block error rate ("frame error rate"), before counting effects of HARQ retries.
 +
* '''UL-HFER''' - Long-term UL transport block error rate, including effects of HARQ retransmission and recovery.
 +
* '''UL-eff''' - UL PHY efficiency in bits per resource element x100.
 +
* '''64QAM''' - True if 64-QAM is enabled for UL.
 +
* '''ULbytes''' - Total number of bytes transferred on UL at the MAC layer, including padding bytes.
 +
* '''DL-eff''' - DL PHY efficiency in bits per resource element x100.
 +
* '''256QAM''' - True if 256-QAM is enabled for DL.
 +
* '''DLbytes''' - Total number of DL bytes transferred in the MAC layer on this connection.
 +
* '''DL-NACK''' - Short-term average HARQ NACK rate for DL. An estimate of DL frame error rate at the UE.
 +
* '''UC-RSSI''' - PUCCH RSSI in dB, on same scale as PUSCH. PUCCH is normally 6 to 20 dB lower than PUSCH.
 +
* '''UC-SNR''' - PUCCH post-despread signal to noise ratio in dB, which should be 6 or higher for a good connection.
 +
* '''UC-miss''' - Fraction of time when PUCCH expected to receive HARQ ACK/NACK or CSI but could not decode anything.
 +
** Shows reliability of PUCCH, with zero being ideal.
 +
* '''Age''' - Age of the connection in seconds.
 +
* '''Idle''' - Idle time of the connection in seconds.
 +
* '''RSRP''' - DL RSSI of reference signals at the UE, in dBm. See [https://en.wikipedia.org/wiki/RSRP Wikipedia RSRP]. For a Lab Kit, -70 to -90 is normal, less than < -90 is weak.
 +
* '''RSRQ''' - DL channel quality at the UE. 0 is perfect, -1 .. -3 is good, less than -5 is poor. This number is a good predictor of DL throughput for this UE.
 +
* '''UL-BSR''' - Estimated number of bytes waiting for UL transmission in the UE.
 +
* '''DL-BSR''' - Number of bytes waiting for DL transmission in the eNodeB.
 +
 
 +
Example:
 +
<pre>
 +
RNTI    PHR    RSSIdB  RSSIdBm UL-SNR  UL-FER  UL-HFER UL-eff  64QAM  ULbytes DL-eff  256QAM  DLbytes DL-NACK UC-RSSI UC-SNR  UC-miss Age    Idle    RSRP    RSRQ    UL-BSR  DL-BSR
 +
61      30      -12    -32    20      2%      2%      15      false  2962    21      false  5314    0%      -26    43      0%      5      0      -100    -3      0      0
 +
</pre>
 +
 
 +
 
 +
== As of r7293 ==
  
 
* '''RNTI''' - RNTI (radio layer connection ID) of this connection.
 
* '''RNTI''' - RNTI (radio layer connection ID) of this connection.

Revision as of 23:13, 23 June 2018

This page documents the enb uepool chans command, by revision, most recent first.


As of r7437

  • RNTI - RNTI (radio layer connection ID) of this connection.
    • If this number is followed by R, it means the connection is marked for release but not yet fully released.
    • If this number is followed by S, that means it is a simulated UE generated internally by the eNodeB.
  • PHR - Power headroom in dB per resource block.
  • RSSIdB - Recent average PUSCH UL RSSI, referenced to the receiver saturation point.
  • RSSIdB - Recent average PUSCH UL RSSI in true dBm.
  • UL-SNR - Short-term average PUSCH UL signal to noise ratio in dB, which should be 12 or higher for a good connection.
  • UL-FER - Short-term UL transport block error rate ("frame error rate"), before counting effects of HARQ retries.
  • UL-HFER - Long-term UL transport block error rate, including effects of HARQ retransmission and recovery.
  • UL-eff - UL PHY efficiency in bits per resource element x100.
  • 64QAM - True if 64-QAM is enabled for UL.
  • ULbytes - Total number of bytes transferred on UL at the MAC layer, including padding bytes.
  • DL-eff - DL PHY efficiency in bits per resource element x100.
  • 256QAM - True if 256-QAM is enabled for DL.
  • DLbytes - Total number of DL bytes transferred in the MAC layer on this connection.
  • DL-NACK - Short-term average HARQ NACK rate for DL. An estimate of DL frame error rate at the UE.
  • UC-RSSI - PUCCH RSSI in dB, on same scale as PUSCH. PUCCH is normally 6 to 20 dB lower than PUSCH.
  • UC-SNR - PUCCH post-despread signal to noise ratio in dB, which should be 6 or higher for a good connection.
  • UC-miss - Fraction of time when PUCCH expected to receive HARQ ACK/NACK or CSI but could not decode anything.
    • Shows reliability of PUCCH, with zero being ideal.
  • Age - Age of the connection in seconds.
  • Idle - Idle time of the connection in seconds.
  • RSRP - DL RSSI of reference signals at the UE, in dBm. See Wikipedia RSRP. For a Lab Kit, -70 to -90 is normal, less than < -90 is weak.
  • RSRQ - DL channel quality at the UE. 0 is perfect, -1 .. -3 is good, less than -5 is poor. This number is a good predictor of DL throughput for this UE.
  • UL-BSR - Estimated number of bytes waiting for UL transmission in the UE.
  • DL-BSR - Number of bytes waiting for DL transmission in the eNodeB.

Example:

RNTI    PHR     RSSIdB  RSSIdBm UL-SNR  UL-FER  UL-HFER UL-eff  64QAM   ULbytes DL-eff  256QAM  DLbytes DL-NACK UC-RSSI UC-SNR  UC-miss Age     Idle    RSRP    RSRQ    UL-BSR  DL-BSR
61      30      -12     -32     20      2%      2%      15      false   2962    21      false   5314    0%      -26     43      0%      5       0       -100    -3      0       0


As of r7293

  • RNTI - RNTI (radio layer connection ID) of this connection.
    • If this number is followed by R, it means the connection is marked for release but not yet fully released.
    • If this number is followed by S, that means it is a simulated UE generated internally by the eNodeB.
  • AVGRSSI - Recent average PUSCH UL RSSI, referenced to a ideal level of 0 dB.
  • CURRSSI - RSSI of most recent PUSCH UL transmission, referenced to a ideal level of 0 dB.
  • UL-SNR - Short-term average PUSCH UL signal to noise ratio in dB, which should be 12 or higher for a good connection.
  • UL-FER - Short-term UL transport block error rate ("frame error rate"), before counting effects of HARQ retries.
  • UL-HFER - Long-term UL transport block error rate, including effects of HARQ retransmission and recovery.
  • UL-eff - UL PHY efficiency in bits per resource element x100.
  • 64QAM - True if 64-QAM is enabled for UL.
  • ULbytes - Total number of bytes transferred on UL at the MAC layer, including padding bytes.
  • DL-eff - DL PHY efficiency in bits per resource element x100.
  • 256QAM - True if 256-QAM is enabled for DL.
  • DLbytes - Total number of DL bytes transferred in the MAC layer on this connection.
  • DL-NACK - Short-term average HARQ NACK rate for DL. An estimate of DL frame error rate at the UE.
  • UC-RSSI - PUCCH RSSI in dB, on same scale as PUSCH. PUCCH is normally 6 to 20 dB lower than PUSCH.
  • UC-SNR - PUCCH post-despread signal to noise ratio in dB, which should be 6 or higher for a good connection.
  • UC-miss - Fraction of time when PUCCH expected to receive HARQ ACK/NACK or CSI but could not decode anything.
    • Shows reliability of PUCCH, with zero being ideal.
  • CQI - Fraction of time that CQI was received correctly on PUCCH.
  • Age - Age of the connection in seconds.
  • Idle - Idle time of the connection in seconds.
  • RSRP - DL RSSI of reference signals at the UE, in dBm. See Wikipedia RSRP. For a Lab Kit, -70 to -90 is normal, less than < -90 is weak.
  • RSRQ - DL channel quality at the UE. 0 is perfect, -1 .. -3 is good, less than -5 is poor. This number is a good predictor of DL throughput for this UE.
  • UL-BSR - Estimated number of bytes waiting for UL transmission in the UE.
  • DL-BSR - Number of bytes waiting for DL transmission in the eNodeB.

Example:

RNTI    AVGRSSI CURRSSI UL-SNR  UL-FER  UL-HFER UL-eff  64QAM   ULbytes DL-eff  256QAM  DLbytes DL-NACK UC-RSSI UC-SNR  UC-miss CQI     Age     Idle    RSRP    RSRQ    UL-BSR  DL-BSR
62      -2      -13     11      7%      2%      44      false   466k    391     false   12M     0%      -18     44      2%      50%     14      0       -70     -3      0       447k
61      -2      3       10      12%     1%      16      false   933     16      false   1454    0%      -18     12      0%      50%     15      0       -83     -5      0       21k