SatSite installation guide

From YateBTS
Revision as of 14:03, 3 September 2018 by Dburgess (Talk | contribs) (RF cable and antenna)

Jump to: navigation, search


satSite 142
satSite 132




Connections


satSite 142


Connector Type Function
Antenna "N" female Bi-directional RF connection to antenna or TMA/TMB
Network A IP-67 RJ-45 / CONEC PN 17-10000 Primary network interface factory configured for static IP
Network B IP-67 RJ-45 / CONEC PN 17-10000 Secondary network interface factory configured for DHCP
Power Binder Series 692 -48VDC input, up to 2 Amp

Note: The "B" interface, the one set for DHCP, is always the one closer to the antenna port.



Mounting the SatSite on the tower

Note: Tower work is dangerous. Do not attempt to climb a tower without proper equipment and training.

Each SatSite is provided with a pair of mounting brackets. These are different for 142 , 132 and high-temperature ("142T") versions.


SatSite 142

Each mounting bracket has

  • a flat or U-shaped plate that attaches to the SatSite radiator
  • a set of 3 bridles for different sizes of poles
  • a set of bolts and nuts and washers for assembly

Please refer to the image Mounting Brackets SatSite 142 for details.

SatSite 142T (high-temperature)

Please refer to the image Mounting Brackets SatSite 142T for details.

Note the extra nylon spacers between the flat plate and the radiator.

SatSite 132

Please refer to the guide Mounting SatSite 123


Power supply

The SatSite operates from -48 VDC. The input is diode-protected against reverse voltage.

The unit is supplied with a 10-meter power cable and an extra connector so that you can make your own cable following the information below.

The unit is supplied with a 200W 48VDC supply that can be used to power it from mains power of 120-240 VAC, 50-60 Hz.

satsite142 power

Power connector details

Pin Function
1 -48VDC in
2 -48VDC in
3 +48VDC in
PE System ground



satsite142-power

Power supply cables

SatSite

  • positive (supply ground, "V+") = brown cable
  • negative (-48 VDC, "V-") = black and grey cables
  • safety ground (G) = green + yellow cable

Mains/Grid

  • mains neutral = blue
  • mains 120-240 VAC 50-60 Hz ("hot" or "live") = brown







Grounding

The installation kit includes a grounding strap that should be attached from the radiator (142) or mounting bracket bolts (132) to a sufficient ground point.

Note: The design of grounding systems is site-specific. Please consult a local electrician for a proper grounding system for your site.

Ethernet

The Satsite has two Ethernet connectors for Network A and Network B.

By design Network B is the port closer to the Antenna

  • Network A has the fixed IP 10.0.3.1
  • Network B will have DHCP IP address

Note: We recommend installing both network cables to the SatSite unit, so that the "A" port can be used to recover the unit if DHCP fails.


Thread the shroud onto the ethernet cable.

Pic 1.png



Attach and crimp the R5-45 connector onto the cable in the standard way.

Pic 2.png



For this step, you need two 19 mm wrenches. Slide the shroud over the connector.

Pic 3 updated.png


The connector will slide completely into the shrowd, further than shown here. Then tighten the gland nut around the cable. When attaching the cable to the SatSite unit, align the connector first, then press it into place, then turn the shroud body to lock the connector. Also check the gland nut is tight and forms a good seal.






RF cable and antenna

Caution.png


Please pay attention: When a SatSite unit is powered, the output can be as high as 20 watts RMS, enough power to cause burns if you come into direct contact with the central conductor in the connector or on the cable. Use caution and avoid working with actively powered radio equipment.

RF cable needs to be connected with caution while rotating it. Its recommended to use spanner 14 mm while connecting the cable

rf-cable-satsite142


Getting started

In order to get started with Satsite , you can either use the static IP or dynamic IP.

1. Using static IP Connect Network A ethernet to PC , and assign the PC static IP address in the network 10.0.3.x /8 Then you can access it via ssh

  • ssh yatebts@10.0.3.1 -p 54321
  • then telnet 0 5037

or via the web interface http://10.0.3.1:2080/lmi The username is yatebts and the password is the serial number

2. Using dynamic IP Connect Network B to your local network and make sure it get DHCP IP address Then you can access it via ssh

  • ssh yatebts@<DHCP_IP_ADDRESS> -p 54321
  • then telnet 0 5037

or via the web interface http://<DHCP_IP_ADDRESS>:2080/lmi The username is yatebts and the password is the serial number


SatSite Configurations

Please refer to:


References

SatSite 142 data sheet