Difference between revisions of "YateSTP Configuration"

From YateBTS
Jump to: navigation, search
(M2UA -> M3UA)
Line 173: Line 173:
  
  
==== M2UA -> M3UA ====
+
==== M3UA ====
  
 
Configure link sets, links and link management in the scenarios with 2'''x'''STPs at each end
 
Configure link sets, links and link management in the scenarios with 2'''x'''STPs at each end

Revision as of 14:12, 23 October 2018

THIS PAGE IS A DRAFT

YateSTP (Signal Transfer Point) is a SS7 router that relays messages between various SEPs (Signaling End-Points) and other STPs.

Two signaling points connected by one link are said to be adjacent.

A collection of links that connect together the same signaling points is called a link set and each link set can contain up to 16 separate links.

A group of link sets used to reach a particular destination is called a route and a combination of routes that can be used to reach the same destination is called a route set.


Interconnect

  • Layer3 -> PC routing
  • Layer4 -> GT (IMSI/MSISDN) routing [ E.164, E.212, E.214 ]
layers L1 L2 L3 L4 L5 L6
tdmcard M2PA MTP3 SCCP TCAP MAP/CAMEL
wanpipe M2UA M3UA ISUP
sctp CiscoSM/SLT
RUDP MTP2
file sigtransport.conf ysigchan.conf regexroute.conf


sigtran-custom.conf

This scenario assumes that there are two STPs at each end (MNO/MVNO)

; SIGTRAN1: MNO1a - MVNO1a
[10.125.125.121:2920]
remote=10.30.132.132:2920
local=10.125.125.121:2920
type=sctp
stream=yes
endpoint=yes
rto_min=200
rto_max=400
rto_initial=400
enable=yes

; SIGTRAN2: MNO1a - to MVNO1b
[10.125.125.122:2920]
remote=10.30.16.132:2920
local=10.125.125.122:2920
type=sctp
stream=yes
endpoint=yes
rto_min=200
rto_max=400
rto_initial=400
enable=yes


; SIGTRAN3: MNO2a - to MVNO2a
[10.125.126.112:2920]
remote=10.30.132.160:2920
local=10.125.126.112:2920
type=sctp
stream=yes 
endpoint=yes
rto_min=200
rto_max=400
rto_initial=400
enable=yes


; SIGTRAN4: MNO2a - to MVNO2b
[10.125.126.111:2920]
remote=10.30.16.160:2920
local=10.125.126.111:2920
type=sctp 
stream=yes  
endpoint=yes
rto_min=200
rto_max=400
rto_initial=400
enable=yes


[general]
bind_strict=yes


ysig-custom.conf

M2PA -> MTP3

Configure link sets, links and link management:

; Connect to MNO STPs, file /etc/yate/stp/ysig-custom.conf
[ls_stp_stp1]
enable=yes
type=ss7-mtp3
netind2pctype=ITU
pointcodetype=ITU
netindicator=reservednational
adjacent=ITU,2001
local=ITU,2011
router=ss7router
link=stp_stp1

[ls_stp_stp2]
enable=yes
type=ss7-mtp3
netind2pctype=ITU
pointcodetype=ITU
netindicator=reservednational
adjacent=ITU,2002                                                                                                                                                                                                  
local=ITU,2011                                                                                                                                                                                                     
router=ss7router                                                                                                                                                                                                   
link=stp_stp2                                                                                                                                                                                                      
                                                                                                                                                                                                                   
[stp_stp1]                                                                                                                                                                                                         
type=ss7-m2pa                                                                                                                                                                                                      
sig=sctp-stp1                                                                                                                                                                                                      
                                                                                                                                                                                                                   
[stp_stp2]                                                                                                                                                                                                         
type=ss7-m2pa                                                                                                                                                                                                      
sig=sctp-stp2                                                                                                                                                                                                      
                                                                                                                                                                                                                   
[sccp-mgm]
remote=2001
remote=2002


M3UA

Configure link sets, links and link management in the scenarios with 2xSTPs at each end

; Connect to MNO STPs, file /etc/yate/stp/ysig-custom.conf
; Define MVNO router, PC: 2011
[to_mno1]
type=ss7-router
transfer=yes
local=ITU,2011
management=snm-mno1
pointcodetype=ITU
enable=yes

[snm-mno1]
type=ss7-snm
local=ITU,2011
router=to_mno1

[sccp2011]
type=ss7-sccp
pointcodetype=ITU
localpointcode=2011
router=to_mno1
management=mgm-mno1
extended-debug=yes
endpoint=true

[mgm-mno1]
type=ss7-sccp-itu-mgm
pointcodetype=ITU
sccp=sccp2011
remote=2001
remote=2002

[gtt2011]
;enable=no
type=ss7-gtt
sccp=sccp2011
debugname=GTT-2011


; Define MVNO router, PC: 2012
[to_mno2]
type=ss7-router
transfer=yes
local=ITU,2012
management=snm-mno2
pointcodetype=ITU

[snm-mno2]
type=ss7-snm
local=ITU,2012
router=to_mno2

[sccp2012]
type=ss7-sccp
pointcodetype=ITU
localpointcode=2012
router=to_mno2
management=mgm-mno2
endpoint=true

[mgm-mno2]
type=ss7-sccp-itu-mgm
pointcodetype=ITU
sccp=sccp2012
remote=2001
remote=2002

[gtt2012]
;enable=no
type=ss7-gtt
sccp=sccp2012
debugname=GTT-2012


; add here ASP settings for each client
[m3ua_2011_2001]
type=ss7-m3ua-client
traffic=unused
sig=10.125.125.121:2920

[m3ua_2011_2002]
type=ss7-m3ua-client
traffic=unused
sig=10.125.125.122:2920

[m3ua_2012_2001]
type=ss7-m3ua-client
traffic=unused
sig=10.125.126.111:2920

[m3ua_2012_2002]
type=ss7-m3ua-client
traffic=unused
sig=10.125.126.112:2920


; Link sets
[2011_2001_ls]
type=ss7-m3ua
routing-context=none
router=to_mno1
client=m3ua_2011_2001
netindicator=national
local=ITU,2011
adjacent=ITU,2001

[2011_2002_ls]
type=ss7-m3ua
routing-context=none
router=to_mno1
netindicator=national
client=m3ua_2011_2002
local=ITU,2011
adjacent=ITU,2002

[2012_2001_ls]
type=ss7-m3ua
routing-context=none
router=to_mno2
netindicator=national
client=m3ua_2012_2001
local=ITU,2012
adjacent=ITU,2001

[2012_2002_ls]
type=ss7-m3ua
routing-context=none
router=to_mno2
netindicator=national
client=m3ua_2012_2002
local=ITU,2012
adjacent=ITU,2002